might reveal a bit of naiveté, but I'll comment anyway.
In "my world", which is Type V construction (i.e., primarily light framed,
wood, CFS, masonry, etc.), there is a need for an occasional steel beam or
three. These structures do not normally require special inspectors, but I
guess with the advent of the IBC, those instances will be fewer. Anyway,
I've always designed my simple steel connections based on bearing load since
the members were usually lightly loaded and did not need the capacity of
A-325 bolts. As soon as I specify A-325 bolts, the "special inspection" flag
goes up. The minimum charge (in the real world) is four hours or $160 to
$250. I realize in a steel building, this isn't a big issue since there are
so many connections and the labor savings of installing fewer bolts can be
realized, but that is just not the case in the structures I design. In my
particular case, the inspector would inspect one connection!
The preferred diameter of bolt is 5/8".
I hope this answered your question.
Regards,
T. William (Bill) Allen, S.E.
ALLEN DESIGNS
Consulting Structural Engineers
> -----Original Message-----
> From: Abolhassan Astaneh-Asl [mailto:astaneh@ce.berkeley.edu]
> Sent: Sunday, October 07, 2007 10:37 PM
> To: seaint@seaint.org
> Subject: AISC Table X (9th Ed.) or Table 10-9a (13th Ed.)
>
> Dear Mr. Allen: Is there a particular reason that you are using A307?
> Could you please give more information on the connection or the structure.
> No specific names or locations of the structure, just enough to
> understand why A307 bolts are used and not A325 or A490? And what is the
> diameter of A307 that you are using?
> In my Steel Design courses, I never had an actual example of use of A307
> to give to my students. This will be very helpful in my teaching.
> Thanks. As for your question, I hope AISC or others , more qualified than
> I am , will help.
> Abolhassan Astaneh,Professor UC Berkeley (www.ce.berkeley.edu/~astaneh)
> -------------------
> From: "Bill Allen" <T.W.Allen@cox.net>
> To: "'Bill Allen'" <T.W.Allen@cox.net>,
> Subject: AISC Table X (9th Ed.) or Table 10-9a (13th Ed.)
>
> What do I use (table or procedure) if I want to use A-307 bolts in a
> single
> plate connection?
>
> T. William (Bill) Allen, S.E.
>
> ALLEN DESIGNS <http://www.AllenDesigns.com>
>
> Consulting Structural Engineers
> V (949) 248-8588 . F(949) 209-2509
> ---------------------
>
>
> ******* ****** ******* ******** ******* ******* ******* ***
> * Read list FAQ at: http://www.seaint.org/list_FAQ.asp
> *
> * This email was sent to you via Structural Engineers
> * Association of Southern California (SEAOSC) server. To
> * subscribe (no fee) or UnSubscribe, please go to:
> *
> *
http://www.seaint.org/sealist1.asp
> *
> * Questions to seaint-ad@seaint.org. Remember, any email you
> * send to the list is public domain and may be re-posted
> * without your permission. Make sure you visit our web
> * site at: http://www.seaint.org
> ******* ****** ****** ****** ******* ****** ****** ********
******* ****** ******* ******** ******* ******* ******* ***
* Read list FAQ at: http://www.seaint.org/list_FAQ.asp
*
* This email was sent to you via Structural Engineers
* Association of Southern California (SEAOSC) server. To
* subscribe (no fee) or UnSubscribe, please go to:
*
*
http://www.seaint.org/sealist1.asp
*
* Questions to seaint-ad@seaint.org. Remember, any email you
* send to the list is public domain and may be re-posted
* without your permission. Make sure you visit our web
* site at: http://www.seaint.org
******* ****** ****** ****** ******* ****** ****** ********